百科.dev
全部条目在线工具AI 编程趋势榜开源项目技术资讯提交条目
登录
< 返回工具列表
A

ATAboy

> 编程语言
开源

ATAboy 是一款用户友好型桥接设备,可让传统 CHS 格式的 IDE (PATA) 硬盘驱动器连接到现代计算机,作为标准的 USB 大容量存储设备。

198 stars0 点赞1 次浏览
访问官网GitHub

工具介绍

ATAboy 是一款用户友好型桥接设备,可让传统 CHS 格式的 IDE (PATA) 硬盘驱动器连接到现代计算机,作为标准的 USB 大容量存储设备。

If you don't want to build your own, the hardware can be purchased here: https://obsoletetech.us/products/ataboy-an-open-source-legacy-ide-usb-bridge


ATAboy is designed for retro computing enthusiasts, data recovery experts, and archivists. Read and write the oldest of IDE hard drives, without the need for an "in-between" vintage computer!

ATAboy is a user-friendly bridge that allows classic IDE (PATA) hard drives to be connected to a modern computer over USB as a standard USB Mass Storage device. While cheap, modern adapters usually only work with newer "LBA" type drives, ATAboy works all the way back to the earliest CHS only, PIO Mode 0, ATA disks. (It will also work with newer LBA type IDE disks, but that's not really what it's designed for.) ATAboy features an "Award BIOS inspired" user friendly UI for drive configuration and setup.


When connected:

  • The IDE drive appears to your computer like a normal USB Mass Storage Device
  • No special drivers are required (Windows, Linux, macOS supported)
  • The device translates USB Mass Storage commands into IDE read/write operations

Hardware Requirements

To get started, you will also need:

  • Any 40‑pin IDE (PATA) hard drive. It may be jumpered master, slave, or cable select.
  • An external PSU to power the drive.
  • A USB-C cable to connect ATAboy to the host computer.
  • Any standard ANSI compatible serial terminal emulator (e.g. PuTTY, Tera Term, minicom, screen, etc.)

Basic drive mount using ATABoy

  1. Connect the IDE ribbon cable to the drive and ATAboy (Note Pin 1 orientation, usually marked by a stripe on the cable)
  2. Connect ATAboy to your computer via USB
  3. Power the drive using external supply
  4. Connect to serial console with terminal of choice (PuTTY shown). 9600 8N1, no flow control. You should see an Award BIOS "inspired" text-based UI appear in the terminal.
  5. Enter the "Auto Detect & Set Geometry" menu
  6. Choose default, or enter geometry manually if needed
  7. Choose "Mount HDD to USB Mass Storage"
  8. That's it! You can now read the drive from your modern OS!

You can save the current ATAboy settings, geometry, etc to EEPROM, which will be restored the next time the device is booted. (This allows auto-mounting also.)

IMPORTANT! If you are working with valuable or irreplaceable data, ensure write protection is enabled before mounting. It is enabled by default for safety. You do NOT want the host OS to touch or bless the disk! Windows VDS/RPC services can often crash if it is unable to write to a drive with damaged/legacy MBR and/or partition tables. This can result in various Windows errors, unable to mount the drive, etc. However, raw data can usually still be accessed via dd, or other raw disk backup software. Regardless, it is STRONGLY recommended the entire drive be dumped to an image file BEFORE disabling write protection, then mounting the drive in Explorer.


Safe Removal

Always use your operating system’s Safely Remove / Eject feature before:

  • Unplugging the USB cable
  • Powering off the IDE drive

This helps prevent:

  • File system corruption
  • Incomplete writes
  • OS-side errors

Known Limitations

ATAboy is a hobbyist and experimental project. You should be aware that:

  • Performance is significantly slower than modern USB to IDE bridges. We're working over USB 1.1 for now. This can cause long mount times, especially in Windows if the disk has file system weirdness.
  • Many legacy disks use unusual geometry, and may require experimentation.
  • Not all OS disk utilities behave the same way

PLEASE NOTE!

Some of the firmware code was written with AI assistance. It has been tested with dozens of drives, and does function well with most. But may be buggy, slow, or unresponsive with certain drives. Please let us know if you find a drive that does or doesn't work right. We'll build a compatibilty list soon.

Use at your own risk!

  • Firmware written in VS Code with Raspberry Pi Pico Extension
  • PCB designed in Kicad
  • Case designed in Freecad

ATAboy is meant to be hacked, learned from, and improved. Have fun, and thank you for trying ATAboy!

Licensing

"ATAboy" is a trademark of JJ Dasher. The open source licenses do not grant rights to use these trademarks.

Firmware

Licensed under GNU GPLv3. See /firmware/LICENSE.

Hardware

Licensed under CERN-OHL-W v2. See /PCB/LICENSE.

Issues· 0 开放

查看全部 Issues在 GitHub 打开

暂无开放 Issues,或尚未同步最近议题。

> 标签

C

暂无评论,来聊聊你的看法吧

> 工具信息

发布日期2026年8月1日
最后更新2026年9月18日
分类编程语言
定价开源

> 相关工具

T
TypeScript
JavaScript 的超集,为前端与全栈提供静态类型
P
Python
通用编程语言,广泛用于 Web、数据与 AI
G
Go
Google 推出的简洁高效系统语言