百科.dev
全部条目在线工具AI 编程趋势榜开源项目技术资讯提交条目
登录
< 返回工具列表
B

bldc-drive

> 编程语言
开源

一款价格低廉、简单的无刷直流电机驱动器,专为使用STM32微控制器的CNC应用而设计

199 stars0 点赞0 次浏览
访问官网GitHub

工具介绍

一款价格低廉、简单的无刷直流电机驱动器,专为使用STM32微控制器的CNC应用而设计

bldc-drive

This is a project developing a simple BLDC servo controller. It is based on an STM32F103 microcontroller.

Some parts, especially the PID control loop is based on development done by user mcm_xyz in cnczone.com forum. Thank you! Check the thread http://www.cnczone.com/forums/open-source-controller-boards/283428-cnc.html

Disclaimer

This software and hardware is provided "AS IS", WITHOUT ANY WARRANTY. The software is released under GPL v2. Authors accept no liability for any harm or loss resulting from use of this hardware or software.

Authors & Contributors

  • original Software by mcm_xyz from cnczone
  • first Version of Hardware&Software in a Git-repo from pekkaroi via https://github.com/pekkaroi
  • Schematic-additions and fork by Philipp Hörauf via https://github.com/Virtex7

Firmware

Firmware is a work-in-progress (and will be for a while :), however following features are included:

  • Trapezoidal BLDC commutation using either HALL sensors or quadrature encoder.
  • Step+Dir input interface with PID position control loop.
  • PWM+Dir input interface in velocity mode.
  • USART communitacation for configuration. Configuration settings saved to flash memory.
  • TODO: Motor Test Mode to simply activate a Motor with a fixed frequency, no encoder needed

Update 1st May 2016

Some updates to the firmware.

  • ADC current limiting implemented. Appears to work OK
  • I created a quick and ugly Python gui for tuning
  • Updated the PID loop to have feedfoward coefficients FF1 and FF2 (like LinuxCNC). This means that the PID output can be adjusted by the requested speed and the requested acceleration. This made the PID tuning a lot easier for me at least, I'm able to get a motor to follow the requested position very well also during acceleration and during constant drive.

Hardware:

First prototype hardware is built and it is working well. However, there are couple of known issues:

  • 6n137 optocoupler is not officially supporting 3.3V supply voltage which is used in the board. In reality they seem to work, but the optocoupler should be changed or additional levelshifting circuitry added on next revision. Also, the optocoupler input circuit supports only push-pull-type encoder output. Many encoders seem to have open drain output. :(
  • Few connectors in the layout missed solder stop openings. They were bit painfull to solder. :)
  • The current amplifier INA27x connection is wrong. The IN+ and IN- should be swapped.

STATUS QUO:

Second hardware revision with the above findings fixed is published. There are no known issues, two servo drives are succesfully driving my CNC router. Pics and videos to come..

HARDWARE TODOs:

  • verify all part-values into the schematic

Issues· 0 开放

查看全部 Issues在 GitHub 打开

暂无开放 Issues,或尚未同步最近议题。

> 标签

C

暂无评论,来聊聊你的看法吧

> 工具信息

发布日期2026年8月1日
最后更新2026年9月18日
分类编程语言
定价开源

> 相关工具

T
TypeScript
JavaScript 的超集,为前端与全栈提供静态类型
P
Python
通用编程语言,广泛用于 Web、数据与 AI
G
Go
Google 推出的简洁高效系统语言