百科.dev
全部条目在线工具AI 编程趋势榜开源项目技术资讯提交条目
登录
< 返回工具列表
R

Reflow-Controller

> 编程语言
开源

重熔控制器 重熔控制器是专为控制各种重熔炉、热板以及其他我脑中浮现的设备而设计的。

356 stars0 点赞0 次浏览
访问官网GitHub

工具介绍

重熔控制器 重熔控制器是专为控制各种重熔炉、热板以及其他我脑中浮现的设备而设计的。

Reflow-Controller

The Reflow-Controller was built to control different kinds of reflow ovens, hotplates and whatever is coming to my mind in the future. It is based on the ESP32-S2 (datasheet) and thus can be programmed to be used with a WiFi App or whatever. Nevertheless, it has an onboard OLED display and three buttons included to be used as a standalone solution either.

The Youtube video shows the assembly of a complete reflow oven system and the first tests.

Features of the PCB:

  • ESP32-S2 MCU
  • 2x MAX6675 thermocouple sensor input
  • 2x Fan output (inductive loads/flyback diodes included)
  • 2x Solid state relay output
  • 3x User button
  • 1x APA102 user LED
  • 1x Buzzer
  • 1x Servo motor output
  • 0,96" OLED display
  • Optional ACDC converter (HLK-PM05, HLK-PM12) which can be separated if not used
  • Optional I2C (QWIIC) connector

GPIOs

The ESP32-S2 is connected like this:

Function GPIO Mode
SSR1 GPIO1 Output
SSR2 GPIO2 Output
Servo GPIO3 Output
Fan1 GPIO5 Output
Fan2 GPIO6 Output
CLK GPIO7 SPI
MISO GPIO9 SPI
MOSI GPIO11 SPI
CS1 GPIO12 SPI
CS2 GPIO13 SPI
Buzzer GPIO15 Output
USB D- GPIO19 CDC
USB D+ GPIO20 CDC
SDA GPIO33 I2C
SCL GPIO35 I2C
Button1 GPIO36 Input
Button2 GPIO39 Input
Button3 GPIO40 Input
LED CLK GPIO37 LED
LED DATA GPIO38 LED
OLED RST GPIO45 Output

ACDC power supply

The upper part of the PCB can be used as a power supply for the whole board as well as the higher voltage outputs (SSRs, Fans). If not used, it can be separated from the main board and may be used in another project where an ACDC adapter is needed.

The main board is equipped with an LM1117 3.3v voltage regulator which can be feed with 15v max. The output voltage of the ACDC power supply is the voltage for the SSR and the fan output channels. If you wanna use a servo motor in your project, make sure that the power supply has the correct voltage for the motor (probably 5v).

The HLK-PMXX module for the upper part of the PCB can be placed in two ways - on the bottom or on the top side. This gives the possibility to mount the whole PCB behind an acrylic glass (or whatever) so that the buttons as well as the OLED display are accessible. The two jumpers can then be used to select which signal is VCC and which one is GND. Keep in mind that there are high voltage pins on the top side of the PCB when mounting the power supply on the bottom side! I've designed a 3D-printable cover, so that these pins cannot be touched accidentally. (Should be mounted in both cases)

The board can also be powered via USB-C, but keep in mind that the output channels and the servo motor are not powered in this case (initially it is just available for flashing the board).

Case & Spacer

As I wanna hide the whole PCB behind an acrylic glass (transparent) I've designed a simple case for the high voltage pins at the top and a spacer at the bottom of the PCB. In the end, the acrylic glass will be laser-cutted with some bridges for the buttons. Distance between PCB and acrylic glass is 5mm.

Assembled reflow oven

Issues· 0 开放

查看全部 Issues在 GitHub 打开

暂无开放 Issues,或尚未同步最近议题。

> 标签

C++

暂无评论,来聊聊你的看法吧

> 工具信息

发布日期2026年8月1日
最后更新2026年9月17日
分类编程语言
定价开源

> 相关工具

T
TypeScript
JavaScript 的超集,为前端与全栈提供静态类型
P
Python
通用编程语言,广泛用于 Web、数据与 AI
G
Go
Google 推出的简洁高效系统语言