百科.dev
全部条目在线工具AI 编程趋势榜开源项目技术资讯提交条目
登录
< 返回工具列表
E

ESP32Picoremote

> 编程语言
开源

ESP32PicoD4TFTRemote 是基于 ESP32 Pico D4 MCU 和美观的 160x80 像素小型 TFT 显示屏的 WiFi 遥控器。此外,还有一个 I2C 传感器接口,可用于连接温度、湿度、光线等传感器。

362 stars0 点赞1 次浏览
访问官网GitHub

工具介绍

ESP32PicoD4TFTRemote 是基于 ESP32 Pico D4 MCU 和美观的 160x80 像素小型 TFT 显示屏的 WiFi 遥控器。此外,还有一个 I2C 传感器接口,可用于连接温度、湿度、光线等传感器。

ESP32PicoD4_TFT_Remote

WiFi remote based on ESP32 Pico D4 MCU and a beautiful 160x80 pixels mini TFT display. Additionally there is a I2C temperature & humidity sensor as well as an accelerometer on board.

Assembling video is on my Youtube.

The power latching circuit ensures that the ESP32 Pico D4 don't need to be in deep sleep mode while in OFF state. This puts it down to around 3µA during 'sleep', due to the battery protection. It can be woke up only by the middle button. The battery protection occupies reverse voltage protection through the mosfet. Overdischarge voltage of the XB5353A is 2.4volts, which is only for safety reasons. The battery voltage should always be checked with the voltage divider, which gives you an estimation of the battery state.

Main components are:

  • ESP32 Pico D4
  • CP2102N USB to serial bridge
  • 160x80px ST7735 13pin TFT display
  • HDC1080 temperature and humidity sensors
  • LIS3DHTR accelerometer
  • WS2812 LEDs
  • XB5353A battery protection
  • SE7401U polarity
  • MCP73831 charging
  • RT9193 regulator
  • Molex 3D antenna

Circuit & PCB

pico32_remote_v1.0 was the initial schematic of this PCB. Unfortunately it occupies a few mistakes:

  • Button two is connected to the ESP32 directly behind the button, which gives VCC directly to one of the GPIOs of the MCU - meh. The 1k resistor should be between the pulldown and the button.
  • Furthermore the footprint of the LIS3DHTR is mirrored (not visible in the schematics).
  • Last but not least the VUSB of the USB-C connector and the power selection circuit wasn't connected properly because the VUSB on one side was just a label and not the name of connection itself - shame on me.

All these mistakes are fixed in version 1.1. Additionally I have added a USB activation diode, which enables the latching circuit ones a USB cable is plugged into the board. This is nice to have if you want to visualize battery charging. Another advantage is that one of the buttons don't have to be pressed during firmware upload.

Code

Check out the code in the 'code' section. It is used in PlatformIO, but can be shifted to Arduino IDE easily. The code is exactly the same.

The ST7735 display can be used easily with the TFT_eSPI library by Bodmer. This library comes with a User_Setup.h to setup the dedicated display you are using. I have attached this file for this specific board in the code section of this repo.

Another nice library to play little GIFs on that tiny display is the AnimatedGIF library by Larry Bank. He shared a nice tool for converting GIFs to a code array as well.

Milled case

It is not yet optimized but the bottom part is looking great. The top part should move left and right while pushing the buttons, unfortunately it doesn't due to the small holes in PCB and bottom part. An easy solution would be to use two elongated holes in the top part (the screw heads would be visible on the top part).

When you have questions then feel free to ask.

Have fun! :)

Issues· 0 开放

查看全部 Issues在 GitHub 打开

暂无开放 Issues,或尚未同步最近议题。

> 标签

C

暂无评论,来聊聊你的看法吧

> 工具信息

发布日期2026年8月1日
最后更新2026年9月17日
分类编程语言
定价开源

> 相关工具

T
TypeScript
JavaScript 的超集,为前端与全栈提供静态类型
P
Python
通用编程语言,广泛用于 Web、数据与 AI
G
Go
Google 推出的简洁高效系统语言