制作一款由 Google Assistant SDK 提供支持的 DIY 机器人调酒机
##In the Spring of 2023, innovation studio and experiential design firm Deeplocal launched Gizmology, a one-year creative technology apprenticeship program for recent high school graduates and underemployed adults in Pittsburgh’s Black community. Supported in part by Deeplocal’s parent company WPP’s racial equity committments, Gizmology’s goal was to advance racial equity in creative and technical fields through on-the-job training and mentorship. Through an initial upfront classroom training spanning nearly four months the Gizmology apprentices, or Gizmos as they affectionately named themselves, learned the foundational skills related to 3D design, electrical engineering, physical computing, fabrication methods (laser cutting/welding/woodworking), and creative technology. Designed as two semesters, Gizmology 1 and Gizmology 2, each semester culminated with a capstone project; the final capstone for the classroom training was to ‘re-create’ a robotic mocktails mixer with Google Assistant built in.
In mid-July, after weeks of interdisciplinary training and exposure, each of the Gizmos chose an apprenticeship track and set-out to complete the final capstone project fulfilling their specific roles. Jason focused on exhibit fabrication, Jordan delved deeper into technical integration, and Justin focused on Mechanical Design, with each pitching in to work as a team and support the assembly. For Creative Tech, Imani and Mecca shared the responsibility of updating and converting the SDK from Python to Node.Js as it was no longer valid; this was no small feat and an amazing accomplishment for a beginning creative technologist. For all the Gizmos, it was evident that the recreation of the robotic mocktails mixer with Google Assistant wasn’t simply going to be a matter of merely following directions, it was going to take creativity, ingenuity, and most importantly- the real world application of the skills they learned to successfully recreate the project as a team. What you’ll see below is the journey of the Gizmos to create the “Gizmology Mocktails Mixer”, complete with six uniquely designed mocktails (from eight different flavors) representing personal connections to each member of the Gizmology team. This DIY robotic home bartender whips up your favorite mixed drinks at your command–in the true spirit of the Gizmos!
Disclaimer: THESE INSTRUCTIONS ARE BEING PROVIDED FOR INFORMATIONAL PURPOSES ONLY AND ARE NOT INTENDED TO BE USED FOR THE PRODUCTION OF COMMERCIAL PRODUCTS. BY EXECUTING THESE INSTRUCTIONS, YOU AGREE TO ASSUME ALL LIABILITY IN CONNECTION WITH YOUR BUILDING AND USE OF ANY DEVICE. DEEPLOCAL DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED WITH RESPECT TO THESE INSTRUCTIONS AND ANY RESULTING DEVICE INCLUDING BUT NOT LIMITED TO WARRANTIES FOR MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, AND NON-INFRINGEMENT. YOU SHOULD USE EXTREME CAUTION WHEN BUILDING AND USING ANY DEVICE PURSUANT TO THESE INSTRUCTIONS. IN NO EVENT SHALL DEEPLOCAL BE LIABLE FOR ANY CLAIM OR DAMAGES, INCLUDING BUT NOT LIMITED TO CLAIMS OR DAMAGES RELATED TO DEATH OR PERSONAL INJURY, PROPERTY DAMAGE, OR PRODUCT LIABILITY.
Features:
Before you get started, you should have a basic knowledge of soldering. You should also have access to a laser cutter. You can find all of the parts we used, along with the exact quantity, supplier, cost, and links to purchase here. Note: In general, we used parts that were readily available, but on the expensive side. This build could be completed with less expense if parts are sourced on Amazon/Alibaba or if lower quality parts are used. Note: All materials used in this build are rated as “food safe.” Liquid does not come in contact with any material that is not food grade safe.
Note: DFXs are all in inches. Please scale according to input of the laser cutter. See attached drawings for design guidance.
*Panels that were revised include: Lid Capture Panel- needed holes for the light wire Pump Relay Control Panel- CAD mount holes for brackets. CAD holes for wires from pumps to power and access for tubes to run through, holes for the relay to be mounted Rear panel- CAD holes for mounting a fan
*Note: We highly recomend a cardboard prototype.
Attach Top Panel with Bottle Capture Panel together with #10-32 x 1/2 inch length button socket cap and #10-32 x 1 inch length ¼ OD standoff.
On the other side, with Lid Capture Panel use 10-32 x ¾ inch length button socket cap fasteners (Optional - Double sided tape can be used to attach the Lid Capture Panel to the bottom of the Bottle Capture Panel).
Note: There is a ¼ inch overhang on the Top Panel. Rear panels are flush with the exception of the tabs.
Note: To ensure pump tubing is food grade safe, please replace with Tygon Clear PVC tubing 3/32 inch ID x 5/32 inch OD (Hardness rating is “Soft” and durometer is 65A). The durometer is imperative to pump and tube life. This can be found on McMaster-Carr.
Remove cover from pumps by depressing snaps on both sides of pump head. Remove tubing that was placed in during shipment. Place food grade tubing into pump allowing 3 inches to remain outside the inlet and outlet of the pump. Also, be careful to not puncture the tubing when installing around the rollers.
The pumps that were available required brackets to be mounted. Brackets were created in solidworks and 3D printed.
Use the Pump/Relay Control Panel and attach the brackets to the eight 1.10 inch diameter holes located on the panel. Place a #8 black rubber washer between the bracket and acrylic to reduce vibration. Use a #2-56 x ½ inch length Phillips pan head machine screw and corresponding nut to fasten the brackets to the acrylic. Use the same screws and nuts to attach the pump to the bracket.
In this version, to save time, we have used an 8 channel Relay module. Attach the 8-Channel Relay Module directly above each pump on the Pump/Relay Control Panel. There will be a 4 bolt hole pattern. Use the #2-56 x ⅜ inch length ⅛ inch OD standoffs (Optional - You can use #2-56 x 1/2 inch length Phillips pan head machine screw and corresponding nut instead of the standoffs.) with number #2 washers underneath each hole before the standoff. Fasten each corner with a #2-56 x 5/32 inch length Phillips pan head machine screw. Note that the red led must be positioned toward the top of the acrylic sheet. Use a #2-56 x ⅜ inch length pan head Phillips machine screw and fasten relays from other side of acrylic.
Tip: When attaching the fasteners, washers and standoffs to the relay module, allow them to be loose. This will help with easy alignment to the corresponding holes on the acrylic than retighten fasteners on relays.
You can 3D print an Arduino Uno mount by using this link to download the file from GrabCAD. We used a Bambu Studio P1P 3D printer. The file takes about 6 minutes to print in total.
Place the Arduino on the mount, matching the holes on the Arduino to the corresponding holes on the mount. Use screws to secure the Arduino onto the mount. Attach the Arduino and the mount onto the back of the pump panel with VHB. You should leave enough room for the the wires from the relay to come through the slot and attach to the pins on the Arduino Uno.
Attach the Raspberry Pi to the back panel using velcore.
For a clearer view of the wiring diagram download the fritzing file.
The electrical system of the Mocktails Mixer uses two control systems. The first is a Raspberry Pi, which handles all of the communication with the Google Assistant SDK. The second is an Arduino Micro that controls the pumps and LEDs. Both of these systems are connected to each other over serial. The Raspberry Pi sends commands to the arduino about what lights and pumps to turn on and the Arduino executes them.
Outside of these two controllers, the Mocktails Mixer has four major hardware systems. They are Power, the Pumping system, Lights, and Audio.
The power system controls the flow of electricity in the Mixer. However, the Mixer uses two different voltages: 12V for the pumps and 5V for the other hardware. You can handle this by using a step-down voltage regulator or a dual-voltage power supply. These are both adequate for the basic build of the Mixer, but if you want to add extra flair (like more LEDs), you may need to use two separate power supplies. Our instructions and BOM use two power supplies.
Note: For safety, we recommend placing the power supply in an external enclosure to keep 110V away from the liquids in the mixer.
In this version of the Mocktails Mixer, we used eight (8) peristaltic pumps. These are rated and recommended for use at 12V, but you can run them up to 24V if you find that the pumps are running too slow. The pumps are all individually switched by a relay controlled by the Arduino Uno.
For visual feedback, we added an LED ring to the Mixer. We used the Adafruit Neopixel. It is very easy to wire and add additional rings, plus the library is easy to use. These draw a decent amount to amperage, so if you want to add more to your build, you will need to size your 5V power supply accordingly.
Last but not least, we used a USB Microphone to speak and order drinks that is connected directly to the Raspberry Pi. We chose to not connect the speaker. If we did, the speaker could be connected to the amplifier on the Arduino’s mounting plate. The amplifier is connected to the Raspberry Pi via a 3.5 mm headphone jack.
To wire the power supply, first connect the AC Lines to their terminals (Black to L or Load, White to N or Neutral, Green to Ground). Next, connect the DC power lines to power supplies. Note: To make the wiring easier to follow, we used red wire for all the 12V lines and green for all of the 5V lines. We kept the all of the Ground wires black because all devices will need to share Ground in order to communicate. Note: We also recom
暂无开放 Issues,或尚未同步最近议题。