百科.dev
全部条目在线工具AI 编程趋势榜开源项目技术资讯提交条目
登录
< 返回工具列表
F

free-dap

> 编程语言
开源

免费、开放地实现 CMSIS-DAP 调试器固件

335 stars0 点赞0 次浏览
访问官网GitHub

工具介绍

免费、开放地实现 CMSIS-DAP 调试器固件

Free-DAP

This is a free and open implementation of the CMSIS-DAP debugger firmware.

Both SWD and JTAG protocols are supported. However JTAG was not well tested due to lack of good targets. If you have any issues with it - let me know and I'll try to help.

Platform requirements

To create a CMSIS-DAP compliant debugger, your platform must:

  • Implement USB HID (and raw bulk for CMSIS-DAP v2) device able to receive and send arbitrary payloads
  • Provide configuration file dap_config.h with definitions for hardware-dependent calls
  • Call dap_init() at the initialization time
  • Call dap_process_request() for every received request and send the response back

CMSIS-DAP version support

Free-DAP library itself is protocol agnostic and implementation of the specific version of the CMSIS-DAP protocol (v1 or v2) is up to the individual platforms.

Currently RP2040, SAM D11 and SAM D21 implementaitons were updated to support CMSIS-DAP v2. Other platforms would be updated if requested or needed by me.

Configuration

For complete list of settings see one of the existing configuration file, they are pretty obvious.

To configure clock frequency you need to specify two parameters:

  • DAP_CONFIG_DELAY_CONSTANT - clock timing constant. This constant can be determined by calling dap_clock_test() with varying parameter value and measuring the frequency on the SWCLK pin. Delay constant value is the value of the parameter at which output frequency equals to 1 kHz.
  • DAP_CONFIG_FAST_CLOCK - threshold for switching to fast clock routines. This value defines the frequency, at which more optimal pin manipulation functions are used. This is the frequency produced by dap_clock_test(1) on the SWCLK pin. You can also measure maximum achievable frequency on your platform by calling dap_clock_test(0).

Your configuration file will need to define the following pin manipulation functions:

  • DAP_CONFIG_SWCLK_TCK_write()
  • DAP_CONFIG_SWDIO_TMS_write()
  • DAP_CONFIG_TDO_write()
  • DAP_CONFIG_nTRST_write()
  • DAP_CONFIG_nRESET_write()
  • DAP_CONFIG_SWCLK_TCK_read()
  • DAP_CONFIG_SWDIO_TMS_read()
  • DAP_CONFIG_TDI_read()
  • DAP_CONFIG_TDO_read()
  • DAP_CONFIG_nTRST_read()
  • DAP_CONFIG_nRESET_read()
  • DAP_CONFIG_SWCLK_TCK_set()
  • DAP_CONFIG_SWCLK_TCK_clr()
  • DAP_CONFIG_SWDIO_TMS_in()
  • DAP_CONFIG_SWDIO_TMS_out()

Note that all pin manipulation functions are required even if one of the interfaces (JTAG or SWD) is not enabled.

Additionally configuration file must provide basic initialization and control functions:

  • DAP_CONFIG_SETUP()
  • DAP_CONFIG_DISCONNECT()
  • DAP_CONFIG_CONNECT_SWD()
  • DAP_CONFIG_CONNECT_JTAG()
  • DAP_CONFIG_LED()
  • DAP_CONFIG_DELAY()

Tools

A complete RP2040 build requres bin2uf2 utility to generate UF2 file suitable for the RP2040 MSC bootloader. This utility can be downloded here.

Binaries

Generally there are no pre-built binaries due to effort required to maintain them and low potential benefit because of custom hardware requirement.

For RP2040 and Raspberry Pi Pico board specifically there is a binary, since it is a standard and a widely available board that has a nonvolatile bootloader.

The UF2 file is located here. Simply boot into a BootROM MSC mode and copy that file to the drive.

I will try to do my best to keep this binary in sync with the code updates, but it is a manual process, so I may forget. Let me know if you have any issues.

The pins used are as follows:

GPIO Function
11 SWCLK/TCK
12 SWDIO/TMS
13 TDI
14 TDO
15 nRESET
0 VCP TX
1 VCP RX
2 VCP Status
25 (LED) DAP Status

Issues· 0 开放

查看全部 Issues在 GitHub 打开

暂无开放 Issues,或尚未同步最近议题。

> 标签

C

暂无评论,来聊聊你的看法吧

> 工具信息

发布日期2026年8月1日
最后更新2026年9月18日
分类编程语言
定价开源

> 相关工具

T
TypeScript
JavaScript 的超集,为前端与全栈提供静态类型
P
Python
通用编程语言,广泛用于 Web、数据与 AI
G
Go
Google 推出的简洁高效系统语言