vr-streambox

Streambox

The VR Audio Proxy in a box.

The Big Picture

The Streambox interacts with VR Site in 2 phases.

Phase 1: Knocking & Registering (via HTTPS/REST)

Default Endpoint: https://voicerepublic.com/api/devices

Knocking Request

GET /:identifier

• The request is always performed against the LIVE system, even if the box will be used for staging or a dev system.
• :identifier is a unique string (the streambox uses the cpu serial)

Knocking Response (Example)

{
  loglevel: 1,
  endpoint: "https://voicerepublic.com/api/devices"
}

• all subsequent request must be performed against the endpoint given as endpoint
• the endpoint might container basic auth credentials
• loglevels are the commonly used loglevels (0-5)

Registering Request

POST /

with payload (example)

{
  identifier: "00000000000000000768172641827",
  type:       "Streambox",
  subtype:    "v4"
}

• identifier is the unique string used during knocking
• type is a string naming the client
• subtype is a string (could for example be a build number)

Registering Response (Example)

{
  name: "Nietzsche",
  state: "idle",
  public_ip_address: "1.2.3.4",
  report_interval: 30,
  heartbeat_interval: 5,
  faye_url: "https://voicerepublic.com:9292/faye",
  faye_secret: "12345678987654321",
  pairing_token: "1234"
}

• name is the name of the device as given by the user, should be displayed
• state is the state of the device, states is either pairing or idle
• public_ip_address the visible public ip (gateway) of the device
• report_interval number of seconds between reports
• heartbeat_interval number of seconds between heartbeats
• faye_url the url to the faye server
• faye_secret the faye secret
• pairing_token a token to identify the device during pairing (coming soon)

NOTE: Faye setup is subject to change, for security reasons.

Phase 2: Start & Stop Stream (via Faye)

Subscription

Using the faye details acquired upon registering, the device has to subscribe to the following channel:

/device/:identifier

Most messages follow the following pattern (but some don't):

• the key event describes the type of message
• the key named after the value of event holds further details
• events (as used in the streambox)
  • start_stream - starts the stream, details in key icecast
  • stop_stream - stops the stream
  • restart_stream - stops and starts with previous parameters
  • eval - evals the code provided in eval
  • exit - exits the ruby process (will be restarted)
  • shutdown - shuts the box down
  • reboot - reboots the box
  • print - print (only in loglevel debug)
  • heartbeat (deprecated)
  • report (deprecated)
  • error - ?
  • handshake - ?

start_stream icecast example:

{
  event: "start_stream",
  icecast: {
    public_ip_address: "1.2.3.4",
    source_password: "kahsdkjs",
    mount_point: "1732673-1298736821-19283792-1263",
    port: 80
  }
}

Publish Heartbeat (required)

The box publishes a heartbeat to channel

/heartbeat

with payload (example)

{
  identifier: "00000000000087434573245",
  interval: 5
}

with pauses of n seconds in between heartbeats, where n is given by heartbeat_interval during registering.

Publish Report (optional)

The box publishes reports to channel

/report

with payload (example)

{
  identifier: "000000000082734873468732",
  interval: 30,
  report: {
    
  }
}

with pauses of n seconds, where n is given by report_interval during registering.

• report details depend on the device, but the output of a box can comfortably be observed in the back office.
• should/could include:
  • load
  • temperature
  • usb devices
  • audio sources
  • bandwidth
  • ... (more ideas in the icebox of pivotal tracker)

Dependencies

All instructions are based on raspbian jessie lite.

By default, raspbian will automatically resize the partitions on startup. Since we want to create an image with as little overhead as possible, this must be deactivated! See the next section for instructions how to do this.

• Download zip from https://www.raspberrypi.org/downloads/raspbian/
• unzip
• dd resulting img to sdcard

E.g.

• on Linux:
  • dd bs=4M if=2016-03-18-raspbian-jessie.img of=/dev/mmcblk0
• on OSX:
  • dd bs=4m if=2016-03-18-raspbian-jessie.img of=/dev/rdisk2
  • please note that you should use rdisk and not disk to address the device, this improves read/write performance considerably
  • also, note that the m in bs=4m needs to be lowercase in OSX
  • even better is installing gnuutils and using gnu's dd which behaves exactly the same as on Linux (except for the device name).

This will take a while. (It takes almost 5 minutes on my machine.) You can use time to find out how long exactly. Or append && aplay to get an alert when done.

Stop Automatic Resizing on Startup

Do this before writing the image to the sd card!

• mount image
• open file cmdline.txt
• remove the part quiet init=/usr/lib/raspi-config/init_resize.sh
• save and unmount the image

Intial Setup on a clean raspbian image

Find the PI in you local network. Connect a display the pi will print it's ip address during boot. Otherwise nmap or nc are helpful to poke around.

Ssh into the pi with forward agent -A.

Username pi, password raspberry.

Step 1: Become root

sudo -i SSH_AUTH_SOCK="$SSH_AUTH_SOCK"

We need to set SSH_AUTH_SOCK so that our forwarded ssh agent is available in the new environment created by sudo.

Step 2: Main Setup

…

Step 3: Adjust boot params & "bios"

To

/boot/cmdline.txt

add

consoleblank=0 quiet

In

/boot/config.txt

uncomment the line

hdmi_force_hotplug=1

Step 4: Type & Subtype

The type of the box is always 'Streambox'.

The subtype is stored in /home/pi/subtype.

If you make a change to the box setup, which is not covered by the git repo, please update the subtype file and the corresponding list of known usb devices.

echo -n "v0.3prototype" > /home/pi/subtype
sudo bash -c "lsusb > /home/pi/streambox/lsusb/$(cat /home/pi/subtype)"

Step 5: raspi-config

• use sudo raspi-config to
  • expand file system (only if this installation will not be used as an image)
  • change the user password to aeg9ethoh0thioji
  • set timezone to berlin (for now)

Step 6: Reboot

If the previous step didn't cause a reboot, reboot!

reboot

Helpful commands

Remote control

Send commands to box from rails console, e.g.

device = '/device/000000008ff66473'
Faye.publish_to device, event: 'eval', eval: '21*2'
Faye.publish_to device, event: 'exit'
Faye.publish_to device, event: 'reboot'
Faye.publish_to device, event: 'shutdown'
Faye.publish_to device, event: 'start_stream', icecast: {...}
Faye.publish_to device, event: 'stop_stream'

Force Restart (kill running ruby processes)

sudo killall ruby

Force Update (if auto update is broken)

(cd streambox && git pull) && sudo reboot

Duplication

Create an image

dd if=/dev/mmcblk00 of=2016-06-14_streambox_small.img bs=32M iflag=fullblock count=42 status=progress

This ensures that only 42 * 32 MB are written, which is about 1.4 GB. This is important, because otherwise the image will have the full size of the SD card it is copied from.

For OSX specific command, see Dependencies.

Write that image to a new card

dd bs=4M of=/dev/mmcblk0 if=streambox_v0-3prototype.img

For OSX specific command, see Dependencies.

Once and only once, I had to do this...

Create a deploy key

ssh-keygen -t rsa -C boxed key

Add the public key to this repo on GitLab.

Check both keys (public and private) into this repo.

TODO

• for production boxes make commands in scripts silent
• set the timezone of organization/venue
  • https://www.raspberrypi.org/forums/viewtopic.php?t=4977&f=5
• sudo dpkg --configure -a sometimes helps and seems idempotent
• sudo bing -e 200 localhost voicerepublic.com
• What happens if we bing from behind a FW?

wget -c https://github.com/raboof/nethogs/archive/v0.8.5.tar.gz
tar xf v0.8.5.tar.gz
cd ./nethogs-0.8.5/
sudo apt-get -y install libncurses5-dev libpcap-dev
make && sudo make install
nethogs -V
sudo nethogs

References

• https://www.raspberrypi.org/documentation/configuration/config-txt.md