Baike.dev
All toolsOnline toolsAI codingTrendingOpen sourceNewsSubmit
Log in
< Back to tools
K

keyer

> 编程语言
Open source

Firmware & goodies for making a KEYER (one-handed chorded keyboard).

396 stars0 likes4 views
WebsiteGitHub

About

Firmware & goodies for making a KEYER (one-handed chorded keyboard).

's Keyer

Firmware & goodies for making a Keyer (one-handed version of a chorded keyboard).

Features:

  • Minimal finger movement: it's like typing with all the keys on your home row all the time
  • Free hand while typing: you can use your other hand to sip tea while typing (or move the mouse - if you're not a tea drinking type)
  • Always near your hand - keyer can be attached to a glove so you can just release it and have both of your hands free. Now you can drink your tea and move the mouse at the same time.
  • Tons of chords: a 10-key keyer (3 keys on thumb, 2 index, 2 middle, 2 ring, 1 pinky) can express up to 215 chords (× 2 when counting hold-chord alternatives). With so many chords you can lose a finger and still touch type (carpenters will love it!)
  • Arpeggios: an additional 2 × 78 arpeggios - rolling motion over two keys that can be executed in two directions and can be used for even more input options.
  • Multiple layers: if the 586 shortcuts available on the base layer are somehow not enough for you
  • Rolling chords: when two subsequent chords you're entering share some finger positions you can only move the finger that changes position. When combined with optimized layouts (see the next point) typing is like walking through the keys one finger at a time.
  • Optimized layout: a bundled layout optimizer will perform a combinatorial search over all possible layouts to find the optimal one for typing the texts that you give it (or for your custom finger press / finger movement cost function). Then learn to type with it in the keyer flight school.
  • **Ergonomic layout **: did you know your fingers share the neuro-motor pathways and can't always move independently? The layout generator will avoid finger combinations that are hard to press.
  • Low-latency: the firmware uses hardware interrupts to be more responsive than polling-based keyboards and it also does debouncing in software to be more responsive capacitor-based debouncers.
  • Power for months: a massive 18650 battery + underclocked CPU + firmware able to sleep without losing the Bluetooth connection + hardware power switch on the board mean that you will charge it about as often as a Casio watch.
  • ️: combine it with smart glasses to control your computer (or smartphone) without looking or touching. It's like Meta EMG wristband but actually working!
  • Easy to build: did you ever play with Play-Doh? This keyer was built with modelling clay (baked in the oven for 30 minutes). No 3D printing. No custom PCBs. You can make it with parts from amazon, a hot glue gun and a soldering iron.
  • Perfect fit: you build it yourself, literally molding it to the shape of your hand. You can't get more ergonomic than that.
  • Cheap to build: it's less than 50 USD to make one yourself. Mechanical keyboards are a cheap hobby now. Who would have thought!

Typing video youtube.com/watch?v=Ijwo7SQQ73Q (from Typeware).

Links (a.k.a. Awesome Keyers )

(Send me your links on Bluesky bsky.app/profile/mrogalski.eu so that I can add them here!)

  • Penti Chorded Keyboard - A software keyer that can run on a touchscreen. Notable for its use of arpeggios.
  • ESP32-BLE-Keyboard - Excellent library for turning ESP32s into custom keyboards.

3d-printed keyers:

  • Keyyyyyyyys! - Can you get scrappier than that?
  • Ignacio's keyboard

Commercial products:

  • Twiddler - 19 tiny keys + touchpad for $229
  • Decatext - 10 large keys + typing guide right on the device for $175 (its author also shared the promo code "Neural" for $15 off!)
  • Typeware - ultra lightweight & probably the best all-around design for $273 (pre-orders only )

Memes:

  • Mobile Text Entry Device -
  • I love the powerglove.
  • Johnny Mnemonic - it's even funnier when you realize it's not a parody

Making your own keyer

Welcome to the bottom of the ergonomic mechanical keyboard rabbit hole.

Let's start with some shopping.

Bill of materials

  • LILYGO T-Energy S3 development board ($9.70)
  • Samsung INR18650-35E 3500mAh Li-ion battery (~$2.95)
  • FIMO professional modelling clay ($2.75)
    • Alternatively, one of the FIMO effect modelling clays if you'd like to make your keyer out of stone
  • 10 × Gateron G Pro 3.0 mechanical switches (~$10)
    • Any other switches of your choice will work
  • 10 × Keycaps (~$8)
    • You only need ten of them so feel free to get the coolest keycaps you can find
  • 1m × AWG 18 rigid, insulated copper wire (~$1)
    • Get it from a local hardware store, the online stores are ripping you off
    • You can come with your development board to see which wire gauge fits through the holes on the board

Total: $34.40 (+shipping)

Tools

  • pliers - for bending the copper wire
  • a knife (or a set of sharp teeth) - for stripping the cable insulation
  • (optional) nitryl gloves - for not getting dirty while working with the modelling clay
  • hot glue gun + hot glue sticks - for attaching the components to a wire scaffolding
  • soldering iron + solder wire - for soldering

Forming a skeleton (day 1)

With all the materials and tools in hand, the first step is to form a metal scaffolding which will hold the switches in convenient positions. Traditional electronics devices tends to have "exoskeletons" - they're supported by an external case that surrounds them and protects them from your greasy fingers. This device is built around an endoskeleton of copper wire. We'll cover this endoskeleton with modelling clay in a moment. I hope you bought the thickest wire you could (while still fitting through the holes on the board) because in this device it's structural.

We'll start with a "GND loop". Cut a section of wire - about 20 or 30cm. Strip its insulation (all of it) & insert it into one of the GND holes on the board. Solder it in place - it should be firmly attached to the board. Insert the battery and take the board in your hand. Position it like you'd like it to stay in your hand and start bending the wire into a loop that goes through all the places where key switches bases are going to be placed. For some extra rigidity (long wire behaves a little like a spring) lead the other end of the wire back into another GND hole on the board. You can take the switches with keycaps and place them so that one of their contact points touch the wire. This will give you a better idea of how the keyer is going to end up looking. Don't worry about it being wobbly - we'll use this property to model it a little in a moment. First complete the loop by soldering the other end of the GND loop to the board. If your GND loop happens to pass near other GND holes, you can insert short sections of wire and solder them to the main GND loop as additional supports. This will increase the rigidity of the construction.

Once GND loop is complete, take your key switches and attach them to the GND loop so that one of their contact points makes an electrical contact. You can solder them directly but it's a good idea to start with some hot glue to hold them in place. In my version I also bent the contacts on the key switches to make them smaller (DIY low profile) and to take less space.

As you're going through the process the keyer is going to become more "complete" and you will be able to bend the wire a little to improve key positioning. Remember that hot glue and solder don't form particularly strong bonds so be careful about bending and ideally use pliers to do that precisely.

One word of advice about key positioning is that I've noticed that the keys are "nicest" to press when the axis of pressing goes straight into the palm of your hand. Motions that go parallel to palm of the hand, motions that extend fingers and motions that move fingers to the side are pretty awkward and uncomfortable. I guess our hands evolved to hold things, rather than poke or flick at them. Some keyboard manufacturers might disagree. Their keyboards look undeniably awesome, but this is your keyer and it should be comfortable to use - so make sure the keys are pressed in the same direction that you'd hold something.

Once you attached all of the keys, it's time to add even more rigidity into our construction. We'll do this by connecting the remaining contact points on the switches to the GPIO holes on the board. They're marked on the board with text that says "IO##". It doesn't matter which IO port you choose, but write down which key goes to which IO port - it's something that will have to be entered in the firmware. Take a short cut of the wire, strip it at both ends. Bend it (with pliers) so that it fits in the hole and goes straight to the switch. Then solder it in place at both ends. It's important that the wires going to the IO ports don't touch the GND loop. Insulation should help with that.

After this step, the keyer should be fairly rigid. Mount the keycaps and see how it feels. It's obviously a little "spiky" but you'll have to endure the pain for the moment. Right now bend the wires to put all the key switches in their right positions.

At this point you can go to the "Flashing Firmware" section and check out how your keyer works! It's good to see if you didn't mess anything up so far. The hardest part is over!

Sculpting with clay (day 2)

Now is the time to open up the modelling clay and use it to cover our keyer. Before you begin, remove the keycaps, as they'll only get in the way. Take a small amount of clay and start shaping it in your hand. Squeeze it and fold in half. Repeat this about twenty times. Modelling clay must be mixed a little to prevent it from crumbling. You'll have to do this with every bit of clay that you're adding to the sculpture.

Once you have your warm and soft piece of clay, slap it on top of the keyer - wherever you want to cover something. It's important to cover the bottom parts of the switches - that's the part that may prick your fingers. Everything else is optional. I decided to keep my development board mostly visible and only covered the wires.

As you're sticking pieces of clay, one after another, you may find the resulting shape a little bit ugly. Turns out modelling stuff out of clay is hard! I've found a couple of tricks that may help you:

  1. Add clay in layers. Take a small ball of clay and place it between two popsicle sticks. Roll it into a flat disc with a rolling pin. Popsicle sticks have a uniform, width so the resulting di

Issues· 3 open

View all issuesOpen on GitHub

No open issues yet, or sync has not completed.

> Tags

JavaScript

No comments yet. Be the first to share.

> Details

PublishedAug 1, 2026
UpdatedSep 17, 2026
Category编程语言
PricingOpen source

> Related tools

T
TypeScript
JavaScript 的超集,为前端与全栈提供静态类型
P
Python
通用编程语言,广泛用于 Web、数据与 AI
G
Go
Google 推出的简洁高效系统语言