Clawdmeter

Clawdmeter

A small ESP32 dashboard I made for my desk to keep an eye on Claude Code usage.

It runs on a Waveshare ESP32-S3-Touch-AMOLED-2.16 as well as a few other alternative boards and pairs over Bluetooth, the splash screen plays pixel-art Clawd animations that get busier when your usage rate climbs. The two side buttons send Space and Shift+Tab over BLE HID for Claude Code's voice mode and mode-toggle shortcuts.

Screens

The device boots into the splash. Tap the screen anywhere to switch to the Usage view; tap again to flip back to the splash.

While the splash is up, the middle (PWR) button cycles animations. Hold the power button for 3 seconds, then release, to put the device into pairing mode — this clears the saved Bluetooth bond and re-advertises. The firmware also auto-rotates animations every 20 s within the current usage-rate group, so a long stretch on the splash isn't just one Clawd on loop.

Hardware

Boards supported out of the box:

• Waveshare ESP32-S3-Touch-AMOLED-2.16
• Waveshare ESP32-C6-Touch-AMOLED-2.16
• Waveshare ESP32-S3-Touch-AMOLED-1.8
• Waveshare ESP32-C6-Touch-AMOLED-1.8
• Waveshare ESP32-S3-Touch-AMOLED-2.06
• Waveshare ESP32-S3-Touch-LCD-1.54
• Waveshare ESP32-S3-Touch-LCD-4

Please check if a pull request exists for your alternative hardware port before opening a new one, providing QA feedback and testing on the same hardware is more valuable than duplicate pull requests.

Porting to another board: the firmware is a thin HAL with per-board folders under firmware/src/boards/. Drop in a new folder and a new PlatformIO env — main.cpp, ui.cpp, and splash.cpp never need to change. See docs/porting/adding-a-board.md for the walk-through and docs/porting/hal-contract.md for the interfaces a port must implement.

Prerequisites

• Linux (tested on Ubuntu), macOS, or Windows 10/11
• PlatformIO CLI
• Linux: curl, bluetoothctl, busctl (BlueZ Bluetooth stack)
• macOS: python3 (the installer sets up a venv with bleak and httpx)
• Windows: python3 3.11+ (the installer sets up a venv with bleak, httpx, and pystray)
• Claude Code with an active subscription

macOS installation

The macOS host pieces — Python daemon, LaunchAgent, and flash helper — were ported by Chris Davidson (@lorddavidson). Thanks Chris!

Flash the firmware

./flash-mac.sh waveshare_amoled_216                       # ESP32-S3 2.16" (auto-detects /dev/cu.usbmodem*)
./flash-mac.sh waveshare_amoled_216_c6                    # ESP32-C6 2.16" variant
./flash-mac.sh waveshare_amoled_18  /dev/cu.usbmodem1101  # ESP32-S3 1.8" (or pass an explicit USB serial port)

The board env name is required. Run ./flash-mac.sh with no args to see the available envs (scraped from firmware/platformio.ini).

Pair the device

After flashing, open System Settings → Bluetooth and click Connect next to "Clawdmeter". The daemon only ever connects to the peripheral this Mac is paired/connected to — it never scans for a nearby device — so once it's connected here the daemon picks it up on its next poll (~60 s).

Install the daemon

The daemon reads your Claude OAuth token from the macOS Keychain (service Claude Code-credentials), polls usage every 60 s, and pushes it to the display over BLE.

./install-mac.sh

The installer creates a Python venv in daemon/.venv/, installs bleak and httpx, renders a LaunchAgent into ~/Library/LaunchAgents/com.user.claude-usage-daemon.plist, and loads it. The first run is launched interactively so macOS prompts for Bluetooth permission.

Useful commands:

launchctl list | grep claude-usage                                          # check it's running
tail -F ~/Library/Logs/claude-usage-daemon.out.log                          # live logs
launchctl unload ~/Library/LaunchAgents/com.user.claude-usage-daemon.plist  # stop
launchctl load -w ~/Library/LaunchAgents/com.user.claude-usage-daemon.plist # start

Linux installation

Flash the firmware

./flash.sh waveshare_amoled_216                  # ESP32-S3 2.16" (defaults to /dev/ttyACM0)
./flash.sh waveshare_amoled_216_c6               # ESP32-C6 2.16" variant
./flash.sh waveshare_amoled_18  /dev/ttyACM1     # ESP32-S3 1.8" (or pass an explicit USB serial port)

The board env name is required. Run ./flash.sh with no args to see the available envs (scraped from firmware/platformio.ini).

Pair the device

After flashing, the device advertises as "Clawdmeter". Pair it once:

# Scan for the device
bluetoothctl scan le

# When "Clawdmeter" appears, pair and trust it
bluetoothctl pair F4:12:FA:C0:8F:E5    # use your device's MAC
bluetoothctl trust F4:12:FA:C0:8F:E5

To re-pair later, hold the power button for 3 seconds then release — the device clears its saved bond and re-advertises.

Install the daemon

The daemon polls your Claude usage every 60 seconds and sends it to the display over BLE.

./install.sh
systemctl --user start claude-usage-daemon

Check status: systemctl --user status claude-usage-daemon

View logs: journalctl --user -u claude-usage-daemon -f

Windows installation

Runs natively on Windows — no WSL required. A system-tray app polls your usage and pushes it over BLE, and starts automatically at login.

Prerequisites

• Native Windows (not WSL).
• Python 3.11+ from python.org — check "Add python.exe to PATH" during install.
• Claude Code installed, with claude login completed. The token is read from %USERPROFILE%\.claude\.credentials.json (falling back to %LOCALAPPDATA%\Claude\ then %APPDATA%\Claude\).
• The repo on a native Windows path (e.g. %USERPROFILE%\Clawdmeter), not a \\wsl$ share — the installer refuses a WSL path.

Flash the firmware

pio run -d firmware -e waveshare_amoled_216 -t upload --upload-port COM5   # use your device's COM port

Run pio run -d firmware with no env to see the available board envs.

Pair the device

The device is a bonded BLE HID keyboard, so pair it once: Settings → Bluetooth & devices → Add device → Bluetooth, then select "Clawdmeter". Pairing is required — it enables the physical buttons and keeps a persistent connection (the device keeps showing your last-synced usage even after the daemon quits). To undo, use Remove device (this disables the buttons).

Install the daemon (recommended)

From the repo root in PowerShell:

powershell -ExecutionPolicy Bypass -File install-windows.ps1

This creates a venv, installs bleak/httpx/pystray/Pillow from the in-repo requirements (no internet downloads), registers a per-user login-autostart entry (HKCU\…\Run, no admin needed), and launches the tray app headlessly (no console window).

Run manually instead (optional)

python -m venv .venv
.venv\Scripts\Activate.ps1        # if blocked: Set-ExecutionPolicy -Scope CurrentUser RemoteSigned, then retry
pip install -r daemon\requirements-windows.txt
python daemon\claude_usage_daemon_windows.py        # runs in the foreground; Ctrl+C to stop

Tray icon and menu

The icon's corner bubble shows state — green Connected, amber Scanning, red Error — and hovering shows the status (Connected · last update HH:MM). A notification fires once when it enters Error (e.g. an expired token). Right-click for the menu:

• Status header — live state + last sync time.
• Start at login — toggle autostart on/off.
• Quit — stops the daemon cleanly; leaves the Windows pairing intact (device keeps its last reading).

Logs and troubleshooting

Get-Content $env:LOCALAPPDATA\Clawdmeter\daemon.log -Tail 30        # view logs
reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Run" /v Clawdmeter /f   # remove autostart

How it works

1. The daemon reads your Claude Code OAuth token — from the macOS Keychain (service Claude Code-credentials) on macOS, or from ~/.claude/.credentials.json on Linux (%USERPROFILE%\.claude\.credentials.json on Windows).
2. It makes a minimal API call to api.anthropic.com/v1/messages — one token of Haiku, basically free.
3. The usage numbers come straight out of the response headers (anthropic-ratelimit-unified-5h-utilization and friends).
4. The daemon connects to the ESP32 over BLE and writes a JSON payload to the GATT RX characteristic.
5. The firmware parses it and updates the LVGL dashboard.
6. The firmware also tracks the rate of change of session % over a 5-minute window and picks splash animations from the matching mood group.
7. The two side buttons are independent of all of this — they send Space and Shift+Tab as BLE HID keyboard input to the paired host directly.

Physical buttons

The board has three side buttons. Left and right send HID keys; the middle (PWR) button cycles splash animations and, held for 3 seconds, triggers pairing mode.

Space and Shift+Tab go out as standard BLE HID keyboard reports, so they trigger in whatever window has focus on the paired host — not just Claude Code.

BLE protocol

The device advertises a custom GATT service alongside the standard HID keyboard service:

JSON payload format (written to RX):

{ "s": 45, "sr": 120, "w": 28, "wr": 7200, "st": "allowed", "ok": true }

Fields: s = session %, sr = session reset (minutes), w = weekly %, wr = weekly reset (