FYSETC Board - 3d printer motherboard for VORON and other open source project.
FYSETC Board - 3d printer motherboard for VORON and other open source project.
SPIDER is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V power supply, which provides powerful energy for fans of various voltages, various RGB light strips and Raspberry Pi. You can build a 3D printer with rich functions through SPIDER. Especially for VORON V2.4, we cooperated with the VORON team in the early stage of design, and many features have been recognized by the VORON team. If you are building VORON, this will be your best choice.
Add 5pin connector for BL-Touch
Switch EXP1 & EXP2 mark(Only mark, not socket)
Add +/- mark
Add room for RaspberryPI USB-A power supply port
You can solder the below USB port, then you can power-up RPI with a USB-A cable. It is USB power-supply port without USB signal.
48v and 24v connector
为了兼容某些主板,如RAMPS1.4,FYSETC mini12864 设置了 RST(R3) 和 KILL(R4) 的可选择电阻。目前,有些主板(S6/Spider)将 KILL 换成 5V,此时,请确认FYSETC mini12864 上 R4处于空贴状态,否则按下屏幕上的按钮会致使 5V 与 GND 短路,长时间操作会导致主板损坏。 In order to be compatible with some motherboards, such as RAMPS1.4, mini12864 is equipped with RST (R3) and KILL (R4) optional resistors. At present, some motherboards (S6/Spider) change the KILL to 5V. At this time, please make sure that R4 is not on the mini12864 (please remove it if it is on the board), otherwise pressing the button on the screen will cause a short circuit between 5V and GND, and long-term operation will cause the motherboard to be damaged.
目前发现有些主板在接上 mini12864,并采用 USB 进行烧录时会导致无法烧录的情况,请去除 R1 10K 电阻。 At the moment , some Spider can't upload the firmware using USB if mini12864 is connected to the board, if you run into this issue, please remove R1 resistor.
If you want to enable a CANBUS network in klipper on the Spider board, please check 4.2.1 chapter Communication interface section.
The Spider v3.0 has an internal CAN transciever, There is a permanent 120 ohm termination resistor soldered to the board, no need to add a jumper to enable it and also no ability to disable it. The CAN port is a JST-XH header located here;
FeaturesSpider PinSTM32 PinPin No.Comment
X-MOTOR(1)X-StepPE1142
X-DIRPE1041
X-ENPE940
X-CS/PDNPE738
Y-MOTOR(2)Y-StepPD855
Y-DIRPB1251
Y-ENPD956
Y-CS/PDNPE1546
Z-MOTOR(3)Z-StepPD1461
Z-DIRPD1360
Z-ENPD1562
Z-CS/PDNPD1057
E0-MOTOR(4)E0-StepPD586
E0-DIRPD687
E0-ENPD485
E0-CS/PDNPD788
E1-MOTOR(5)E1-StepPE65
E1-DIRPC137
E1-ENPE54
E1-CS/PDNPC148
E2-MOTOR(6)E2-StepPE21
E2-DIRPE43
E2-ENPE32
E2-CS/PDNPC159
E3-MOTOR(7)E3-StepPD1239
E3-DIRPC433
E3-ENPE859
E3-CS/PDNPA1577
E4-MOTOR(8)E4-StepPE134
E4-DIRPE097
E4-ENPC598
E4-CS/PDNPD1158
TMC Driver SPI (SPI4)MOSIPE1445
MISOPE1344
SCKPE1243
End-stopsX-MINPB1453Share with X-DIAG
X-MAXPA124Share with E0-DIAG
Y-MINPB1352Share with Y-DIAG
Y-MAXPA225Share with E1-DIAG
Z-MINPA023Share with Z-DIAG
Z-MAX(Probe)PA326Share with E2-DIAG
FAN/RGBFAN0PB035
FAN1PB136
FAN2PB2/BOOT137
LED-RPB692Can be used for fan3
LED-GPB591Can be used for fan4
LED-BPB793Can be used for fan5
5V-LED(WS2812)PD384Share with flash indicator(Bootloader)
HeatingE0-HeaterPB1554
E1-HeaterPC865
E2-HeaterPB389
Heated-BedPB490
TemperatureTE0(THERM0)PC015A 4.7kOhm 0.1% temperature sensor pull up resistor is used,PT1000 can be connected directly. For PT100, an amplifier board must be used.
TE1(THERM1)PC116A 4.7kOhm 0.1% temperature sensor pull up resistor is used,PT1000 can be connected directly. For PT100, an amplifier board must be used.
TE2(THERM2)PC217A 4.7kOhm 0.1% temperature sensor pull up resistor is used,PT1000 can be connected directly. For PT100, an amplifier board must be used.
TB(THERM3)PC318A 4.7kOhm 0.1% temperature sensor pull up resistor is used,PT1000 can be connected directly. For PT100, an amplifier board must be used.
EXP2LCD_D7PD1/CAN-TX182Share with CAN-TX1
LCD_D6PD0/CAN-RX181Share with CAN-RX1
LCD_D5PC12/MOSI3/TX5/SDA280
LCD_D4PC10/SCK3/TX3/478
LCD_ENPC11/MISO3/RX3/479
LCD_RSPD2/RX583
ENC_CPA8/SCL367
BEEPPC9/SDA366
EXP1RESETNRST14
ENC_APC6/TX663
ENC_BPC7/RX664
SD-DETPB10/SCL247
SD-MISOPA6/MISO131
SD-MOSIPA7/MOSI132
SCKPA5/SCK130
CSPA4/CS129
EEPROM(4K) I2C Pin-OutSCLPB8/SCL195Connect to 24LC32(4K EEPROM)
SDAPB9/SDA196Connect to 24LC32(4K EEPROM)
Pi_PWR/UARTTXPA9/TX168
RXPA10/RX169
SWD DebugPA13/SWDIO72only used for debugging now and can be used for other purposes.
PA14/SWCLK76only used for debugging now and can be used for other purposes.
FeaturesSpider PinSTM32 PinPin No.Comment
X-MOTOR(1)X-StepPE1142
X-DIRPE1041
X-ENPE940
X-CS/PDNPE738
Y-MOTOR(2)Y-StepPD855
Y-DIRPB1251
Y-ENPD956
Y-CS/PDNPE1546
Z-MOTOR(3)Z-St
No open issues yet, or sync has not completed.